insta lube kit installed

[vxfocus]

here are some pics of the insta lube kit installed..
it was a bit tricky finding a spot for the tank..
had to make a bracket for the mounting hardware that came with it
http://i405.photobucket.com/albums/pp139/kenhalford/1374015431.jpg
and the tank installed
http://i405.photobucket.com/albums/pp139/kenhalford/1374015463.jpg
here is a shot of the t fitting for the inlet hose and sender unit
http://i405.photobucket.com/albums/pp139/kenhalford/1374015379.jpg
the gauge on the tank showing the pressure
http://i405.photobucket.com/albums/pp139/kenhalford/1374015303.jpg
and a final install shot tucked under the air inlet pipe and maf sensor
http://i405.photobucket.com/albums/pp139/kenhalford/1374015344.jpg

[nocturnalVX]

What is it? I Googled it, but didn't see any info.

[JAMAS]

What is it? I Googled it, but didn't see any info.

I googled it too....


http://www.engineprelube.com/howitworks.html

[vxfocus]

What is it? I Googled it, but didn't see any info.

thats it..
it is an engine prelube system delivers oil to the oil galley/bearing before each start up

[Scott Larson]

The neat thing is, it simply holds pressure from the previous engine-run and then when you turn the key before the next start-up it releases the pressurized oil into the oil galleys prelubing the bearings. Really simple and effective. Similar systems have been used in aviation for years...

[evillecutter]

seems like a good idea - wondering why cars dont have these on there in the first place - something else to go wrong?

[vxfocus]

seems like a good idea - wondering why cars dont have these on there in the first place - something else to go wrong?

car companies dont want the engines lasting forever....no one would buy a new car

[Knigh7s]

I've been looking at a similar product, Accusump (https://www.cantonracingproducts.com/cgi-bin/commerce.cgi?search=action&category=2410). I like your install as well. Pretty clean.

During my engine rebuild, I'm really thinking about putting one in along with a low oil pressure warning light.

[vxfocus]

I've been looking at a similar product, Accusump (https://www.cantonracingproducts.com/cgi-bin/commerce.cgi?search=action&category=2410). I like your install as well. Pretty clean.

During my engine rebuild, I'm really thinking about putting one in along with a low oil pressure warning light.

you will need something to pre lube the engine before your first start up..thats why i started lookin around and found the insta lube

[JHarris1385]

I gotta do something soon...I just burned 3 quarts in 500-1000 miles.

[Scott Larson]

Hate to say it JH but you may have the dreaded plugged piston oil return holes that seems to be so prevalent these days. As our VX's reach their prime, more and more people are starting to experience the problems that seem to plague these little beasties as they age. Best of luck, hope you find an affordable fix! :thumbup:

[evillecutter]

I gotta do something soon...I just burned 3 quarts in 500-1000 miles.
dont feel too bad i burn 1 - 1.5 per 1000k

[Knigh7s]

you will need something to pre lube the engine before your first start up..thats why i started lookin around and found the insta lube

Now, a bit curious, do you pre-fill the bottle with oil before first start? I read that it pressurizes as the engine is running, and then it will pre lube at next start. So unless there is oil and pressure in the bottle for the very first start, it wouldn't work for what we are needing right? As in pre lubing before initial start after an engine rebuild.

Updated: Also, I've used Assembly Lube (http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product_engine-assembly-lube-(4-oz)-permatex_12028851-p) several times with great results rebuilding my 4G63 motor (1g eclipse). Redline (http://www.redlineoil.com/product.aspx?pid=136&pcid=17)makes one too.

[Scott Larson]

You would be correct. The accumulator only charges after initial run-up. I suppose you could pre-charge it by filling with oil and then pressurizing with compressed air. They make pre-lube pressure bottles specifically for that purpose. Back in the days of distributor-ignition driven by the oil pump shaft you simply took a discarded distributor shaft and spun the pump with a drill until pressure built on the gauge, not quite so easy these days.

[vxfocus]

Now, a bit curious, do you pre-fill the bottle with oil before first start? I read that it pressurizes as the engine is running, and then it will pre lube at next start. So unless there is oil and pressure in the bottle for the very first start, it wouldn't work for what we are needing right? As in pre lubing before initial start after an engine rebuild.

Updated: Also, I've used Assembly Lube (http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product_engine-assembly-lube-(4-oz)-permatex_12028851-p) several times with great results rebuilding my 4G63 motor (1g eclipse). Redline (http://www.redlineoil.com/product.aspx?pid=136&pcid=17)makes one too.

correct i filled the bottle leaving 3/4 inches from the top.there is a schrader valve to ad pressure...turn the key and it filled the oil galley up before first start up

[Knigh7s]

Nice! Thanks guys, I learnt me something today!:p:p

[44ficus44]

ahhh u all suck... now I want this too....

[evillecutter]

ahhh u all suck... now I want this too....

lol this site is full of that!!