Urgent

[JHarris1385]

Alright I have accomplished the T-Bar crank. I had to to fit my new 265/75-16's. The main problem is the tire rubbing the back front fender walls.? T-Bars were a pain at first but cake in the end. At first that nut was hard as H3ll to budge even after spraying PB on it. So I drove it around for about a day, to find the nuts extremly easy to turn.

But my problem is, well not really a problem, becuase I cant wait to do it. I got my 912's in the mail and need to get more instructions on the bj flip and spring installation. I know there is the Triath intructions which are great but I can not for any reason get the pictures to work along with them.

Question is; is there anyone out there with pics of the srping installation and bj flip to help me? I am a novice at all of this but learning quickly.

Please so I can conquer this task this weekend help me with

1.) All Tools needed
2.) Instructions
**3.) PICS to go with instructions....

Thanks

[ZEUS]

I lifted mine with the 912's and adjusted the torsion bars but didn't flip the ball joints. It aligned just fine so I am not sure you have to do it... preference? I wanted to flip them but the bolts would not come off so we would of had to cut the bj's off and I didn't have any new ones so I left them as is. The rear springs... you just have to jack the VX up really high to get them out (that's what we did anyway) - the 912's are the same length as the OEM springs so it's easy enough to put the new ones in. So really, all you need is the tool to turn the torsion bar bolts and a good jack I guess.

[JHarris1385]

What is the jack point in the back? Dumb question I bet, but I just want to make sure..

Also is it primarily a slip out, slide in new ones kind of procedure?

[Ldub]

Also, the rear springs go in a lot easier if you remove the lower shock attachment.

Pay close attn. to the orientation of the stock springs as they come out...there is a top & a bottom.

Look at how the bottom spring mount engages the end of the coil.

[Ldub]

Jack up the rear (I'm assuming you have a floor jack, as opposed to a bottle jack) under the center of the axle as high as it'll go & put your jack stands under the frame just aft of the lower link attachment points.
Release pressure from the jack, allowing the rear end to drop down a bit.
Remove the lower shock mounts, then allow the axle to drop all the way.
This ought to dis-engage the springs.

[ZEUS]

Good call Ldub - forgot about the shocks. I don't know if you'll like this method... but SPAZZ and I put the floor jack (with a big chunk of wood on the lifting arm) under the fuel tank. We actually lifted the rear end high enough to get the tires off the ground and pried out the stock springs - no jack stands. I was nervous but it did work. Looking back, I would have taken off the rear tires and placed the VX frame on tall jackstands like Ldub said. And keep an eye on the parking brake cable when jacking - you might have to un-bolt it from the control arm so you don't stretch or break it.

[Ldub]

You wanna tell the kid he needs a left hand monkey wrench ?, or should I.

[Triathlete]

Here is a LINKto the pics that should acompany my write up. Hopefully they will help!

[Kenny]

Here's plantisuzoo's Ball Joint Flip instructions too on flipping it.

http://www.planetisuzoo.com/articles...p/Spacer_Howto

Also if you still need to get your head around it (I know I did when I first looked into it...)
Here's the Upper arm with the Ball Joint removed:



And here it is with the ball joint flipped,




When putting it bak together, it takes some pressure to hold the a-arm in place to but the bolt back on. Use this brilliant idea from ldub to lever the arm in position- I wish I did it this way instead of having a freind stand on it...




Good luck!

[JHarris1385]

Well Im done and I would have to say it is a 2 out of 10 on the diffuculty scale. My only problem was I forgot to take the lower shock mounts off at first. And even worse was the spring would not stay level in place before I unlifted the VX, so I took shoe string to straighten it out while I lowered it. But once again im am rushed and did not have time to post pics. But trust me I got some good ones. Oh and I also did not flip the bj yet. Is that just for alignment purposes or does it relieve stress on the cv's?



PS.....I LOVE THE LIFT.

But dizam the turning radius sucks.