Yeah, that's why I opt to have a shop do my brakes. This is one job I feel is best left to the pros. Brakes are something you don't want messed up.
Bart
Yeah, that's why I opt to have a shop do my brakes. This is one job I feel is best left to the pros. Brakes are something you don't want messed up.
Bart
Kenny did a really nice write up on replacing his front brake rotors that also included repacking the front bearings. Check out this thread:
http://www.vehicross.info/forums/showthread.php?t=11324
There was also a write up on one of the other Isuzu sites that I downloaded, but can't find the link right now. It doesn't look too tough, and actually I'm about to tackle replacing the rotors and brake pads on all four corners and repacking the front bearings. I'm waiting for warmer weather so if it goes horribly wrong I can ride my bike to work while a shop fixes my screw ups. I would have a shop do it in the first place, but....well I'm cheap, and I'm kind of looking forward to getting grease under my fingernails.
"The major difference between a thing that might go wrong and a thing that cannot possibly go wrong is that when a thing that cannot possibly go wrong goes wrong, it usually turns out to be impossible to get at or repair."
-Douglas Adams, Mostly Harmless
Well - much to report...
First off, thanks for the link to the wonderful write-up MSHardeman!! My forum searches didn't find that one for some reason. :-( I found a different thread last night at home (and the planet Isuzu links), and after reading about needing a special, hard-to-find hub tool, retapping screw holes, repacking bearings, etc. just to get at the rotors, I decided that this was something better left to the dealer, especially since I didn't have a whole weekend anytime soon to spend on the project, so I returned the rotors & pads I bought from Autozone.
This morning, I called the dealer to find out how much they wanted for the job, and my head almost popped off...
$843.95 to replace front pads & rotors and repack bearings!!
HS!!! WTF?!?! Are you freaking kidding me?!
Oh, and they weren't showing the rotors ($250 a piece!) in the distribution system, so they might need to be shipped from Japan, so it could take a month just to get all the parts (Isuzu is no longer restocking their part inventory in the US, but will provide them from Japan as needed). Welcome to our collective future, my friends...
Needless to say, I will not be taking it to the dealer for a brake job. I can get all the parts from Autozone for about $150. I guess I will find a weekend to devote to this to save the other $700 (or find a mechanic that will install the Autozone parts).
yea thats about the right ballpark.. i took mine in for the bearing repack, they recommended doing my brakes, i said ok to the fronts since it was already being taken apart and asked them to give me a set of rear pads
and i would do them myself.. still wound up costing me about 800.. and it took them 3 days because apparently the guy put everything back together wrong, so they called me and said umm sorry its going to be another day or two cause we have to order this and this and this
FOUND IT!! I knew that I downloaded an indepth how-to regarding repacking the front bearings (see link below), but this may be the same one that you found. In the instructions they tell you how to modify a Ford (I think) hub tool into the hard-to-find Isuzu version. I don't remember reading about re-tapping holes so maybe I should read it again before I go diving into this.
http://www.planetisuzoo.com/articles...Bearing_Repack
I'm with Dub, though. I don't have darn near $800 to spend on a bearing repack/ disc replacment, and I really don't want some shop jockey trying to get my VX in before lunch and forgetting to replace half of the stuff he took out. I've actually never had an issue with any shop I've been to, but I've heard horror stories of mechanics forgetting to put oil pan plugs back in during an oil change. OUCH!!
I say give it a shot.
That hub tool is unnecessay, just use a punch or screwdriver and gently tap with a light mallet, it'll come right off. To reinstall do the reverse and check the preload with a fishing scale.
The reasonable man adapts himself to the world; the unreasonable man persists in trying to adapt the world to himself. Therefore all progress depends on me.
If you want, you can PM me for details - or when you're ready to do it, I can put up a few more pics with instructions in this post.
Some thoughts to start with....
Replace bearings if you are doing the front hub, there is a lot of repetitious work and grease integrity is compromised when you pull off the hub. For hub removal, a Hub tool is not really required. Fish spring scale is easy to find. But I would get an impact screwdriver for those soft Phillips screws. I would also strongly suggest getting new snap rings to replace old ones. If not doing bearings at this time (Dooo-eeeet),then I would put the hub assembly in a plastic bag as you take it off, don't let dirt get into the grease. Plug the back opening so dirt won't fall is as you take the rotor off the hub.
As for bearing re-pack.
Suggest replacing bearings, not just repack, since you are in up to your elbows anyways.
And RENT A GOOD BEARING REMOVAL/INSTALL TOOL - that will save you hours and hours and hours of time.
Get new seals, don't re-use old ones.
It's a hoot to do. Not hard, just time consuming.
Last edited by Kenny : 04/10/2008 at 03:03 PM
No planes involved, I'm sure. Do you know how much a rotor weighs? It would double the cost to fly it here. I'm sure they ship parts on the slow boat (the one from Japan, though).