RADO's Off Road Rig- Build Thread

[LittleBeast]

Awesome!

[SomeoneElse]

Great looking build!

[Triathlete]

Wow, side by side really shows the difference in size between the 10 and12 bolt diffs.

[VXorado]

Wow, side by side really shows the difference in size between the 10 and12 bolt diffs.

I know!!! The 10 bolt is tiny and makes me a little worried about overall strength when locked. I'll be very "selective" in using the front locker.


Per Jo's Advice, I decided to get started on the diff swap this last weekend. Feeling ambitious, I dropped the front axle and swapped the 10 diff. It was a pretty straight forward process, but I did have a couple notes.

Indy4x did the gearing & locker install on the 10-bolt. The diff came with a U-joint drive shaft flange which needed to be swapped to fit our CV drive shaft. The drive shaft flange bolt requires a 30mm socket and an impact wrench for removal. Here's a pic to compare the open diff vs. ARB diff.


The diff drop procedure in the how-to section states the steering linkage needs to be removed. The pic below demostrates that the diff dropped can be completed with the linkage in place. Skip dropping the linkage to save time & effort during a diff drop.


BartManS4 was nice enough to give me a hand on Saturday. His newly painted VX looks great and I had a blast driving the 5-speed to the autoparts store. Thanks Scott.

[JoFotoz]

...........

IPer Jo's Advice, I decided to get started on the diff swap this last weekend. :

...not sure if it was advice, sage or otherwise......

....., or a simple "Hey..dont do what I Idid !!"

Two fully locked VX's this year...Look Out!



Jo

[bartmanS4]

BartManS4 was nice enough to give me a hand on Saturday. His newly painted VX looks great and I had a blast driving the 5-speed to the autoparts store. Thanks Scott.

Thanks for letting me hang out and learn my way around the VX drivetrain.
Unfortunately, I had to leave to help out a friend whose Land Rover Discovery overheated heading up to Blackhawk. It turned out to be as easy as bypassing the heater core since one of those lines blew. I told him not to push his luck but he went on up to Blackhawk anyway. Got stuck in traffic for an hour or two and then promptly lost $300 when he did get to the casino. He should have realized that when your car breaks down going to the casino it's a bad omen.

Scott

p.s. Don't get a friend with a Land Rover!

[VXorado]

I installed the rear ARB locker on a cold snowy day. Everything went really smoothly except I didn't remove the ABS speed sensor before removing the axle shafts. I shredded one sensor and broke the other trying to remove it. I haven't had working ABS in a while... really not too concerned about the speed sensors.

Axle shaft pulled to remove 3rd member. Remove 4 axle bolts, brake caliper & speed sensor. The axle will slide out with little effort.


Speed Sensor 1


Speed Sensor 2


Tip: Use a jack after removing the 3rd member bolts to split the seal and make removal a breeze.


3rd member comparison


The lockers haven't been hooked into air yet and i'll be working on that this week. The re-gear to 4.56 is great so far. Better acceleration and the trans is able to stay within a better RPM range on the highway- no more up/down shifting when driving 70+ MPH.

[Edan96]

How much did it cost you to get the whole car blue?

[VXorado]

Around $400 for the vinyl wrap.

It's been 6 months since the install and it still looks great. I hoping it doesn't get too scratched up on the trails.

[VXorado]

I recently installed the winch and it's ready for recovery. I incorporated a skid pate into the winch plate which does sit below the bumper but has little affect on the approach angle. The winch plate sits directly on the frame rails and still needs tweaking in the future. The edges are 90 degree angles and stick out a bit from the rounded bumper but I may end up using the corners for a small stinger bar. Here's a couple pics... I thought I uploaded more to photobucket but can't find them for whatever reason.






Today I continued building SFIFS kits. My initial test fits are working well and I'll be able to test it thoroughly in Moab.

[gunbarrelvx]

Wow. This is one heck of a build thread and we live ten miles away from each other. I need to buy you a beer one of these days and get some more ideas for mine. Wrapping up a lot of work on it this month and running out of things to do.

[44ficus44]

Wow. This is one heck of a build thread and we live ten miles away from each other. I need to buy you a beer one of these days and get some more ideas for mine. Wrapping up a lot of work on it this month and running out of things to do.

trust me, u can never add too much nor run outta ideas..... i said that 5 months ago."finally done" and the VX just keeps looking meaner by the day.. i need more time for all the projects hehe

[VXorado]

Sure we can meet up sometime gunbarrelvx, i'll have some free time after the Moab meet.

For every project I finish, I think of a few more projects to start. Seems neverending...

[vt_maverick]

Sure we can meet up sometime gunbarrelvx, i'll have some free time after the Moab meet.

For every project I finish, I think of a few more projects to start. Seems neverending...

Just wait till you have a kid, you'll find less time to think about new projects and even less time to work your existing list off.

[VXorado]

Just wait till you have a kid, you'll find less time to think about new projects and even less time to work your existing list off.

I'm sure my days are numbered for no consequence VX spending. It's actually why I've been trying to finish all of these big projects now... might not have the time or money in the future.