3.8L Series II w/ SC swap?

[bartmanS4]

So wait, will the 3800 bolt up to our 4L30e or not? Someone said earlier in this thread that it would not and would need an adapter. I know the 3800 and 3400 (which is a 60 deg V6) - both are typically used in FWD vehicles - share the same bellhousing bolt pattern.

I don't know for sure but everything I've seen as far as specs go says it should work. LeonR said it won't work but I don't know what info he's working with. He may be right though. I do have an AR5 bellhousing sitting in my garage. If I could find a L67 to test fit it to...

I didn't know you could retain the TOD with the AR5 - that's the 5 speed used in later Troopers (1999-2002) isn't it?

Yes, four that I know of have been done including mine.
http://www.vehicross.info/forums/sho...light=ar5+swap

So assuming that the 3800 will bolt right in, why hasn't this swap been done already? Is there a big issue with motor mounts or something? Seems the F body parts like exhaust manifolds should make this easy?

I think someone with an Amigo did it but no one has done this on a VX to the best of my knowledge. I suggest you do it and document it well so that when I do it I can learn from your mistakes.

[thrashercharged]

When I get around to pulling that 4L30e out of that Trooper I'll fit it to a L67 block and see if indeed they fit and take some pictures.

Do you or anyone already know of any fitment issues? Does the oil pan / starter clear or is that an unknown? Anyone already look at the width? Does it fit between the rails?

I suppose the AR5 does away with any tranny controls issues but I'd think the 4L30e and the 4T65e that the L67 came with are close enough so the L67 PCM can control the 4L30e with some wiring and programming.

The TOD has a controller completely separate from the engine/trans controls right? And so does the ABS? I'd assume all they really need from the PCM is engine RPM or something like that so that might be an issue. I wonder if it got this info via a CAN or GM ClassII bus or something? That'll be something to look into. I guess that'll be the only hic-up, the communication with the TOD/ABS stuff since the engine will not be running off the Isuzu controller.

[thrashercharged]

So I have a question about that TOD with the AR5 - Isuzu never had these working together from the factory right? The VX never got a AR5 and all the Trooper's with AR5 didn't get the TOD but got a conventional transfer case instead, right?

So did you just bolt the AR5 onto the TOD and it fit and just worked? Any negatives? If not, why didn't Isuzu offer that combo in the Trooper?

[bartmanS4]

AR5 will accept the TOD with minor grinding relief near the shifter housing. See the link above for details.
TOD works great with the AR5 and you get a better crawl ration because of the 1st gear being 3.95. I've since swapped my TOD out for a manual 2H, 4H, 4Lo TC but only because I want a larger crawl ratio.
As far as anyone who has driven the AR5/TOD combo we ALL agree Isuzu should have made them this way.

[circmand]

AR5 will accept the TOD with minor grinding relief near the shifter housing. See the link above for details.
TOD works great with the AR5 and you get a better crawl ration because of the 1st gear being 3.95. I've since swapped my TOD out for a manual 2H, 4H, 4Lo TC but only because I want a larger crawl ratio.
As far as anyone who has driven the AR5/TOD combo we ALL agree Isuzu should have made them this way.

These small Crossover SUVs were already at $32,000+ At that the price point affected the sale. A bigger better Tranny probably would have added to the sticker.

[thrashercharged]

@LeonR - yeah, the GN was a BOP RWD pattern. Regarding the LS4, I've a few concerns:

1. It's longer, so harder to fit behind the radiator
2. No factory RWD exhaust manifolds ready to bolt on
3. Harder to find in boneyards than the 3800
4. I have to admit I haven't priced 'em, but they've got to be more costly than the L36 or L67 in boneyards? The Flint engine plant made almost a million or more 3800's so they're everywhere.
5. Something about the starter needing to be mounted differently?

Aside from these reasons, I'm also just more familiar with the 3800's and their control systems and integrating it into another vehicle, etc. and I know very little in comparison about the LS4. I've ready access to 3800's and don't have a LS4, so the choice is obvious for me. But regardless, I think for anyone, the much more affordable build will be the 3800 from many reasons - one being that you can use the stock PCM and wiring harness that you'll probably get for free with the engine - no need to spend the money on Megasquirt, etc. and stock either the L36 or L67 will give comparable power to the original 3.5L (so you don't have to worry about stressing the 4L30e) and if trans durability isn't a concern, the L67 can be modified to make plenty enough power.

I have to agree that if you have your heart set on a V8 for that V8 exhaust note if nothing else, the LS4 is definitely the way to go over any other LS series due to the FWD bolt pattern. So how cheap is a LS4? Are they easy to find? So no one wants them due to the bolt pattern?

Anyone have any comments on how the TOD and ABS controller interface with the PCM?

@circmand - I see you're from Greenville, MS? I'm from MS - my wife's from Greenville but it's been over 20 years ago. Got married there @ 1st Baptist. Is the drag strip still open? I got stopped by the cops drag racing a buddy's '84 Mustang GT against another buddy's brand new '86 GT while a guy that just bought a GN off the showroom floor paced us ('cause it was no contest that it was faster!) at 3:00 AM on Hwy 82 coming into town back in the day when we were young and stupid! We stop at Doe's Eat Place whenever we're back now days and don't mind spending the money!

[circmand]

@circmand - I see you're from Greenville, MS? I'm from MS - my wife's from Greenville but it's been over 20 years ago. Got married there @ 1st Baptist. Is the drag strip still open? I got stopped by the cops drag racing a buddy's '84 Mustang GT against another buddy's brand new '86 GT while a guy that just bought a GN off the showroom floor paced us ('cause it was no contest that it was faster!) at 3:00 AM on Hwy 82 coming into town back in the day when we were young and stupid! We stop at Doe's Eat Place whenever we're back now days and don't mind spending the money![/QUOTE]

Just moved to G-Ville back in May. This place is dead. I haven't been to Doe's due to the previously mentioned $$$$. No on the drag strip I get frustrated driving around here due to people driving in both lanes 10-15 under the speed limit.