Results 1 to 11 of 11

Thread: Just a quick question

  1. #1
    Member Since
    Jun 2006
    Location
    1999, Black, Vehicross 0512
    Posts
    303
    Thanked: 0

    Just a quick question

    So on the drive home today the brake light came on and the pedal went to the floor.

    Not fun!

    Pulled into the church parking lot and steam started coming out the front drivers side. I added some brake fluid and slowly made my way home. It is dark now so I can't verify, but I am hoping it is a ruptured brake line.

    The question I have is: Are the brake lines for the VX the same as on the Rodeo or Trooper?

  2. #2
    Member Since
    Jun 2004
    Location
    99 Astral Silver VX #1872 + 99 Ironman WIP
    Posts
    10,613
    Thanked: 1

    Wrench

    Quote Originally Posted by dietz99vcross View Post
    So on the drive home today the brake light came on and the pedal went to the floor.

    Not fun!

    Pulled into the church parking lot and steam started coming out the front drivers side. I added some brake fluid and slowly made my way home. It is dark now so I can't verify, but I am hoping it is a ruptured brake line.

    The question I have is: Are the brake lines for the VX the same as on the Rodeo or Trooper?
    Should be...the set at Indy is for "all Isuzu vehicles".

    http://www.independent4x.com/Isuzu-B...-Set_p_21.html

    Good luck with the fix...

  3. #3
    Member Since
    Oct 2012
    Location
    2001, Proton, 0586
    Posts
    445
    Thanked: 0
    My guess is that your caliper got stuck, overheated the rotor/caliper and "boiled" the fluid.

    So the "steam" was actually brake smoke.
    96 Eclipse Spyder GSX (already turbo, AWD swap)
    93 Eagle Summit AWD (4G63 turbo swaps)

  4. #4
    Member Since
    Jun 2006
    Location
    1999, Black, Vehicross 0512
    Posts
    303
    Thanked: 0
    Pretty sure its not the caliper. I can see liquid inside the engine bay as well as under the vehicle. While it was sitting parked and the engine was running if I stepped on the brakes I with the hood up I could see the steam each time I pumped the brakes.

  5. #5
    Member Since
    Oct 2012
    Location
    2001, Proton, 0586
    Posts
    445
    Thanked: 0
    Yea, that suggests a broken line. It is just less likely . What source of heat was it hitting to steam up? It would take a HOT exhaust manifold or overheated rotor to evaporate the brake fluid like that.

  6. #6
    Member Since
    Jun 2006
    Location
    1999, Black, Vehicross 0512
    Posts
    303
    Thanked: 0
    Not bad, just got the VX back from the shop/ $7 for a new line. $10 for new connection, $7 for new brake fluid and some labor. Gotta love this Michigan salt, and the fact that the thing s almost 15 years old. Turns out the connection at the end of the line rusted/corroded and the leak was right at the connection. But it goes and stops again which is nice.

  7. #7
    Member Since
    Dec 2005
    Location
    2001, Dragon Green, 1342
    Posts
    2,393
    Thanked: 0
    Quote Originally Posted by dietz99vcross View Post
    Not bad, just got the VX back from the shop/ $7 for a new line. $10 for new connection, $7 for new brake fluid and some labor. Gotta love this Michigan salt, and the fact that the thing s almost 15 years old. Turns out the connection at the end of the line rusted/corroded and the leak was right at the connection. But it goes and stops again which is nice.
    sure do not miss those Michigan winters and SALT. Since one rust through, think come springtime, I'd be doing a very thorough inspection of the rest of the system, might not have a church parking lot to cruise into next time
    Greetings, Earthling. We come in peace... Never mind "Paris to Dakar", the VehiCROSS looks ready for the Martian desert.

  8. #8
    Member Since
    Jun 2006
    Location
    1999, Black, Vehicross 0512
    Posts
    303
    Thanked: 0
    Thinking about this a little more and while the salt and rust most likely contributed to the issue the culprit in reality may be the lack of common sense of the owner. The other day when it finally reached 40 degrees outside I got this idea to play in the snow. I was curious how well the VX would do driving up and over the rather large snowbanks bordering the driveway. It acted more like a snow plow until the tires in the opposite corners started spinning. When I was done I had snow packed in all the front orifices that I needed to clean out by hand. Perhaps this same snow bank decided to do some rearranging underneath at the same time. None the less it probably is time to switch out all the lines to the set listed above at independent4x

  9. #9
    Member Since
    Feb 2007
    Location
    2000 Proton VX - 0776
    Posts
    9,258
    Thanked: 0
    Quote Originally Posted by dietz99vcross View Post
    ... the culprit in reality may be the lack of common sense of the owner.
    H8 to tell you ... but yer starting to sound more-n-more like me everyday
    [SIGPIC][/SIGPIC]

    Put a smiley after you say that Bub.

  10. #10
    Member Since
    Oct 2012
    Location
    2001, Proton, 0586
    Posts
    445
    Thanked: 0
    Quote Originally Posted by dietz99vcross View Post
    Not bad, just got the VX back from the shop/ $7 for a new line. $10 for new connection, $7 for new brake fluid and some labor. Gotta love this Michigan salt, and the fact that the thing s almost 15 years old. Turns out the connection at the end of the line rusted/corroded and the leak was right at the connection. But it goes and stops again which is nice.
    Wow, that is just sad to hear, I HATE RUST . Was this connection at the master cylinder or at the flexible line?

    Sounds like you have an honest mechanic! This is one of those repairs where mechanics can really take advantage of customers.

  11. #11
    Member Since
    Jun 2006
    Location
    1999, Black, Vehicross 0512
    Posts
    303
    Thanked: 0
    It was on the flexible line. As for the mechanic like all the others before him, he seems reasonable until that one time when he doesn't. But I have been using him for quite a while and he seems fair. I don't like paying the book rate on the labor, but he is quick and willing to work with me on things.

Similar Threads

  1. Quick question
    By PontiacPureBred in forum VX Talk...
    Replies: 16
    Last Post: 09/14/2013, 04:42 AM
  2. Quick question
    By Steve Bourmas in forum VX Troubleshooting...
    Replies: 9
    Last Post: 08/27/2009, 02:20 PM
  3. Quick BFG question
    By SRCHN in forum VX Talk...
    Replies: 2
    Last Post: 07/11/2006, 01:46 PM
  4. Quick question...
    By shoota77 in forum VX Troubleshooting...
    Replies: 2
    Last Post: 11/30/2005, 06:17 PM
  5. Quick Question??
    By XCross69 in forum VX Troubleshooting...
    Replies: 7
    Last Post: 10/27/2003, 07:34 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
$lv_vb_eventforums_eventdetails