Page 1 of 2 1 2 LastLast
Results 1 to 15 of 18

Thread: Drivetrain vibration

  1. #1
    Member Since
    Jun 2002
    Location
    1999, Ebony, VX, #1679
    Posts
    8,422
    Thanked: 3

    Drivetrain vibration

    When accelerating I am getting a severe vibration/bind in the drivetrain from 20 to 36 mph. Above that it goes away. RPMs stay smooth, shifts are smooth, no abnormal tod lights (work as they are supposed to), no strange noises other than the sound of the vibration. Front end has manuel hubs and they are unlocked. Trans mounts are tight. Thinking trans. What else is a possibility?
    Billy Oliver
    15xIronman
    My Sponsors:
    Accelerate3Coaching
    TriSports.com (PM me for 1 time use 20% off code)

  2. #2
    Member Since
    Nov 2009
    Location
    2001Proton 1432, ex 2001 Dragon Green Mica 0168 (RIP May 2017)
    Posts
    3,590
    Thanked: 31
    Does it happen at the same speed no matter what gear it's in, or does it happen at the same RPM if it's in different gears?
    Live, Love, Forgive and Never Give Up

  3. #3
    Member Since
    Jun 2002
    Location
    1999, Ebony, VX, #1679
    Posts
    8,422
    Thanked: 3
    Same speed. RPMS make no difference nor does the gear. I have shifted it down and manually shifted it and it does the same regardless of RPM. Only thing I have not done is try it in 4lo...will do that next time I take it out near some dirt.

  4. #4
    Member Since
    Feb 2010
    Location
    2001 VX 1320 -- Ebony
    Posts
    728
    Thanked: 19
    I'd check the u-joints in the rear drive shaft.
    2001 Ebony VX and 1989 Custom 383 Corvette

  5. #5
    Member Since
    Nov 2009
    Location
    2001Proton 1432, ex 2001 Dragon Green Mica 0168 (RIP May 2017)
    Posts
    3,590
    Thanked: 31
    Wheel balance and bearings as well.

  6. #6
    Member Since
    Jun 2002
    Location
    1999, Ebony, VX, #1679
    Posts
    8,422
    Thanked: 3
    U joints are tight...no play. Will grease them to make sure.
    Pretty sure it's not wheel bearings. It is more of a binding type vibration. All wheel weights are still in tact.

  7. #7
    Member Since
    Jun 2009
    Location
    99 Matte Midnight Sand Met... oh nevermind. VX #0377...Project ZU
    Posts
    2,656
    Thanked: 4
    Have you tested for this vibration with the hubs locked? Could just be from the halfshafts or tcase spinning without load.

  8. #8
    Member Since
    Jun 2002
    Location
    1999, Ebony, VX, #1679
    Posts
    8,422
    Thanked: 3
    I've been driving with the hubs unlocked for the last 8 years.

  9. #9
    Member Since
    Jun 2009
    Location
    99 Matte Midnight Sand Met... oh nevermind. VX #0377...Project ZU
    Posts
    2,656
    Thanked: 4
    Sure but things can wear out after 8 years... like the chain in the t-case. Maybe it will even get worse with the hubs locked and help you find the issue.

  10. #10
    Member Since
    Feb 2010
    Location
    2001 VX 1320 -- Ebony
    Posts
    728
    Thanked: 19
    Clutches can cause shutter. The equivalent in an auto is the torque converter...which is one option. i don't know how to check this. Though you probably need it on a lift and listen with a stethoscope as you run up wheel speed (off the ground).

    Another idea is a motor mount. Check for engine play when you rev up in park. Or put foot on brake in drive and have someone else look at engine shifting.

    On mine, the u-joints weren't so much "worn out" as binding as they rotated. You could hear them at hwy speed. you can probably rule this out.

    Places like NTB and/or Certified Transmission perform diagnosis for free! :-)

  11. #11
    Member Since
    Jun 2002
    Location
    1999, Ebony, VX, #1679
    Posts
    8,422
    Thanked: 3
    New info...
    Took it out today and put it in 4lo...no vibration.
    I can feel the vibration transmitting more through the tcase shifter than the trans shifter.
    No vibration transmits through the steering wheel.

    I think I'm going to drain the tcase and check the fluid and put new fluid in and see if that does anything.

  12. #12
    Member Since
    Jun 2002
    Location
    1999, Ebony, VX, #1679
    Posts
    8,422
    Thanked: 3
    Thanks for all the suggestions. Will keep hunting down the problem.

  13. #13
    Member Since
    Dec 2013
    Location
    1999 Astral Silver 0291, 2000 Kaiser 0419
    Posts
    190
    Thanked: 4
    Whoops, wrong thread
    Last edited by simonsayz1 : 03/08/2016 at 06:13 AM

  14. #14
    Member Since
    Jul 2003
    Location
    '01 Ebony #0939
    Posts
    2,142
    Thanked: 5
    Did you grease the slip joint on the drive shaft too when greasing the u-joints?

  15. #15
    Member Since
    Jun 2002
    Location
    1999, Ebony, VX, #1679
    Posts
    8,422
    Thanked: 3
    Yep, all 3 zerks are freshly greased.

Similar Threads

  1. Found my new drivetrain...
    By Triathlete in forum Chit-Chat ...
    Replies: 6
    Last Post: 09/20/2011, 07:14 AM
  2. Drivetrain noise gone!!!
    By VX crazy in forum Ldub's After Midnight Topics
    Replies: 8
    Last Post: 07/07/2011, 06:37 AM
  3. VX drivetrain descended from?
    By haulin79 in forum VX Talk...
    Replies: 2
    Last Post: 06/26/2006, 04:43 AM
  4. Drivetrain
    By coolk41 in forum VX Troubleshooting...
    Replies: 14
    Last Post: 08/23/2004, 11:20 AM
  5. Clunk Sound in the drivetrain
    By dtruax in forum VX Talk...
    Replies: 5
    Last Post: 06/25/2003, 03:13 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
$lv_vb_eventforums_eventdetails