Overhead Lights
ok, i got ahold of some driving lights....so i tackled the chore of running wiring and mounting them today...
did a write up while i was at it!
i unfortunately did not do a write up on how i wired them into the ignition because that can be changed per however you want them to turn on...
once again, taken with a camera phone...so forgive the crappy pics...
start with running the wires through the car however you please and up to the top of the rear like so-
![](http://www.vehicross.info/gallery/data/3222/0421091050-01.jpg)
once you remove the spoiler with a 10mm socket there is a hole with a grommet in it for the 3rd brake light, i removed the grommet because there was no way the wiring i used would fit through it...
![](http://www.vehicross.info/gallery/data/3222/0421091050-02.jpg)
so, i got the wiring to the roof through that pre-drilled hole (therefore sealed properly to avoid rust and cutting holes in the roof that arent factory
![](http://www.vehicross.info/gallery/data/3222/0421091051-00.jpg)
next, i drilled a hole through the end of the spoiler to reduce water movement...
![](http://www.vehicross.info/gallery/data/3222/0421091051-02.jpg)
![](http://www.vehicross.info/gallery/data/3222/0421091053-00.jpg)
i had to remove the actual LED from the spoiler to help me run the wiring...
![](http://www.vehicross.info/gallery/data/3222/0421091055-00.jpg)
use a fish-tape to get the wire to go to the end of the spoiler from the center
![](http://www.vehicross.info/gallery/data/3222/0421091057-00.jpg)
buy a grommet to fit the hole drilled
![](http://www.vehicross.info/gallery/data/3222/0421091113-00.jpg)
i chose to run whats called a 'conductor wire' that we use in the car audio field to help us wire 4channel amps...basically its a 4ga wire with 9 wires inside of it. i plan on running a lot of lights so i figured instead of running 8 individual wires it would be easier to run conductor...
![](http://www.vehicross.info/gallery/data/3222/0421091118-00.jpg)
next i purchased a trailer connector so that i can remove the roof rack if necessary without having to un-wire...wired up
![](http://www.vehicross.info/gallery/data/3222/0421091149-00.jpg)
zip tied to the roof rack to keep it from hitting the roof on rough surfaces
![](http://www.vehicross.info/gallery/data/3222/0421091149-01.jpg)
![](http://www.vehicross.info/gallery/data/3222/0421091515-00.jpg)
i ran the wiring along the side of the rack to the front...where i purchased 2 90 degree CB antenna mounts designed for semi mirrors, to mount the actual lights to...![](http://www.vehicross.info/gallery/data/3222/0421091150-00.jpg)
i mounted the CB antenna mounts, and mounted the lights to those...i think they turned out well
![](http://www.vehicross.info/gallery/data/3222/0421091515-01.jpg)
next i wired up the relay and switch to the ignition
![](http://www.vehicross.info/gallery/data/3222/0421091515-02.jpg)
here's the completed look...they havent been adjusted, so one looks dimmer but its not..
![](http://www.vehicross.info/gallery/data/3222/0421091521-00.jpg)
heres a close up
![](http://www.vehicross.info/gallery/data/3222/0421091522-00.jpg)
outside my install bay
![](http://www.vehicross.info/gallery/data/3222/0421091527-00.jpg)
in front of my best buy
![](http://www.vehicross.info/gallery/data/3222/0421091541-00.jpg)
please let me know if there are any other pics you need me to take, i still have the interior torn apart...
enjoy!
pbkid
"Do Not Seek Praise. Seek Criticism."
"If You Can't Solve A Problem, It's Because You're Playing By The Rules."
"The Perosn Who Doesn't Make Mistakes Is Unlikely To Make Anything."
-Paul Arden